How To Set Up Mirage Deer Camera

Wildgame Mirage User Manual

Model Numbers: M18B19-ix, M20B19CO33-9, M20i52A26-9, M16i8W26-8,M18i8A26-8, M22B19-21, M18i19-9, M20B38CT39-9, M16B19-viii, M16i28MS2-8, M18i8B2-8, M18i8W26-9, M20i8B2-9, M16i19-8, M18B8T18-8, M18i38D2-viii, M18i19M-9, M20i28MS18-9, M16B31DE2-eight, M18B38D2-8, M22i19-21

Mirage

Battery Installation

i. Open up the door at the bottom of the photographic camera past unlatching the locking tab.

2. With the camera facing open, open the battery compartment cover by sliding the latch to the left.

iii. With the lesser of the camera towards you lot, Brand certain to insert the batteries into the camera with the positive ends towards you where marked positive and the negative ends towards you where marked negative.

NOTE:
Do not mix onetime and new batteries. Do not mix alkaline, standard (carbon-zinc) or rechargeable (nicad, ni-mh, etc) batteries.

4. Shut battery compartment cover. To latch the embrace merely pull the latch slightly to the left every bit you close the battery compartment comprehend.

5. Load SD memory carte du jour (up to 32GB) into the SD card slot with the connectors facing up.

Power

ON:

1. To plow the unit of measurement ON printing and release the power button.

2. Check the battery level icon to ensure the batteries only installed incorporate the proper charge level. If so, you are ok to go on with photographic camera employ.

NOTE:
LCD bicycle through camera information.
PIR moving picture number >
Remaining pictures > Time .

OFF:

ane. To turn the unit of measurement off, first wake up the LCD screen and then depress and hold the power button until the LCD turns off.

Ability Save

1. After 30 seconds without whatsoever buttons being pushed, the LCD will turn off and camera enters into Power Salvage or Gear up Mode.

two. The LCD screen can be awakened by pressing the Power button briefly.

Notation:
The LCD volition not "wake up" when camera is writing to retentiveness.

Examination Mode

one. LCD Ready Mode: The camera volition automatically enter Ready Mode if a button is not pressed for greater than thirty seconds.

2. LED Status Calorie-free: During the starting time 30 seconds of the LCD Ready Way, the red light volition illuminate when a PIR event is triggered. After the LCD turns off, the scarlet light will blink 2-three seconds when photo is taken. After 2 minutes, all indicator lights will plow off until a button is pressed.

Settings

TIME:
1. To change date and time, start by pressing and releasing the enter navigation button to set the 60 minutes.

two. Press the + or – navigation push to go up or down in sequence.

Appointment:
ane. Press the enter navigation push button after setting the minute to change the Date.

2. Press the + or – navigation push to go up or down in sequence.

3. When the Mean solar day is ready, repeat steps one and two to prepare the Month and Year.

Location

1. Printing the Enter navigation button while Location is selected. The first character will be blinking.

2. Press the + or – navigation push to go up or down in sequence. Press the Enter navigation button when the grapheme shown is what you desire and move to the next character.

iii. Repeat steps 1 and two to set the rest of the characters. Press the Enter navigation button to skip spaces and salvage the location proper noun.

PIR Manner

i. Press the Enter navigation button while PIR Mode is selected. The highlighted option volition be blinking.

2. Press the + or – navigation push to move to different options. Press the Enter navigation button to save the setting.

PIR MODE:
STILL: The camera takes nonetheless photographs.
VIDEO: The camera takes xv second videos.

PIR Active

1. Press the Enter navigation button while PIR Active is selected. The highlighted option volition be blinking.

ii. Printing the + or – navigation button to motion to dissimilar options. Press the Enter navigation push button to save the setting.

PIR Active:
24 60 minutes: The PIR tin can be agile at all times.
Day: The PIR tin be active in daylight hours only.
Night: The PIR tin be active in nighttime hours simply.

PIR Sensitivity

1. Press the Enter navigation button while PIR Sense is selected. The highlighted choice will be blinking.

two. Press the + or – navigation button to movement to unlike options. Printing the Enter navigation button to save the setting.

PIR SENSE:
HI: The PIR detects the smallest motion.
MED: (Default) The PIR detects well-nigh common size movements.
LO: The PIR detects merely larger movements.

Exposure

one. Press the Enter navigation button while Exposure is selected. The highlighted option will be blinking.

ii. Press the + or – navigation push button to move to different options. Press the Enter navigation button to relieve the setting.

Resolution

1. Press the Enter navigation button while Resolution is selected. The highlighted pick will exist blinking.

2. Press the + or – navigation push button to movement to unlike options. Printing the Enter navigation push to relieve the setting.

RESOLUTION:
HI: Images will be at the highest resolution but take up the well-nigh space.
MED: Images will be at medium resolution and take up average infinite.
LO: Images will exist at the lowest resolution and take upwards the to the lowest degree infinite.

Filibuster

1. Press the enter navigation push while Filibuster is selected. The highlighted option will be blinking.

two. Press the + or – navigation button to move to different options. Press the Enter navigation button to save the setting.

DELAY:
The time before the camera is able to take some other picture.
PIR Mode: minimum 2s

Image Stamp

PICTURES Display:

A- Fourth dimension
B- Date
C- Moon Stage
D- Location
E- Photo Count

Format SD Card

SDXC CARDS ARE Not SUPPORTED

Having trouble with your SD bill of fare? Try this.

Connect the SD card to your estimator. If
your computer has an SD bill of fare slot you tin insert the SD carte du jour straight into the port.
NOTE: If y'all are using a MicroSD card, y'all will need an adapter to let it to fit into
standard SD menu ports. If your reckoner does not have an SD card port built-in, you tin
use an external USB card reader that plugs into any USB port
on your computer.
Click the Start or Windows menu and select Computer (Windows Vista/seven) or My Computer (Windows XP). For Windows 8 users, blazon "estimator" and click the Figurer icon in the Apps search results.
Right-click the drive alphabetic character associated with your memory device, then select "Format"
Ensure FAT32 is selected nether "File Organization"
Ensure "Quick Format" is checked
Click "Start"

Mounting

1. When mounting to a tree, showtime remove the clip from one terminate of the strap so you tin slide the strap through the slots located on the dorsum of the photographic camera. Once the camera is attached identify the clip back on to the strap. Then, wrap the strap around the tree and clip the two ends together.

Pull the excess material so that the camera is straped tightly to the tree.

IMPORTANT TIPS:

Recommended distance from target surface area is 25-30 feet for optimal imaging quality.
To improve the quality of your images, endeavour not to mount the unit facing the rising or the setting sun in order to avert direct sunlight into the camera lens.
If mounting to a feeder unit or dusty environment, be sure to clean the camera lens cover, incandescent flash cover, and the PIR sensor comprehend on a regular basis.
Periodically bank check the mounting of the camera to insure information technology is not loose.
Brand sure that you securely latch the door closed each and every fourth dimension you lot use the unit, equally the moisture seal will non exist activated unless closed properly.
Check batteries oft to insure no corrosive build-up, every bit this may cause impairment to the camera.

Retrieving Images (SD Card Reader)

A. First, remove the SD Card from the photographic camera unit of measurement itself by pressing on it to where it automatically ejects.

B. Next, insert the SD menu into your SD bill of fare reader.

C. One time inserted into your computer it may automatically launch "AutoPlay", a window recognizing a new Secure Digital Storage Device (the SD Card).

D. If so, information technology should list several options for the next steps (not limited to the following):

Motion-picture show Options
a. Import pictures
b. View pictures
c. Copy Disc
d. Transfer pictures
General Options
a. Open folder to view files

Due east. Select the method from the list provided that best suits your requirements. If the option is fabricated to "View pictures", you can so view the images located on the SD Card and dispense them equally needed.

F. If your figurer does not automatically launch the AutoPlay window recognizing the Removable Disk (the SD Carte), then you will demand to become to the "Get-go Carte" at the bottom left of your screen and select "Calculator". The summary view volition so be illustrated on the right manus side of the window where by the "Devices with Removable Storage" will be listed. The figurer will recognize the reader as "Secure Digital Storage Device". Please select "Secure Digital Storage Device" from this menu (or double click on the graphical icon).

Chiliad. This will then direct y'all into the SD Menu file folder. Images are in the MEDIA binder.

H. In one case open, you volition then see all of the photo files that are located on the SD Card. Select each prototype individually to view. The default viewing browser for your computer volition then automatically launch.

I. Repeat for viewing all or other photos.

J. If y'all decide that you want to delete the image, select the paradigm past placing your cursor on it and clicking your mouse merely once. Right click on your mouse and select delete. This volition delete the prototype permanently, so be admittedly sure you want to do this earlier selecting delete.

Warranty

DISCLAIMERS

WGI Innovations, LTD is non responsible for harm, expense or injury caused by the unauthorized use of, alterations to, improper connectedness of and abuse or fail of the WGI Innovations™ products.

WARRANTY

For the warranty to be in effect, annals your product at wildgameinnovations.com. Follow the onscreen directions to complete the process.

WGI Innovations, LTD will supersede all workmanship defects free of charge for I (1) Year after the date of purchase every bit long every bit your warranty is in effect. This warranty DOES NOT Cover damage, expense or injury caused by unauthorized repairs, alterations, improper connection, shipping, abuse, theft, accident, neglect or collateral loss. When returning product(s) for service you lot MUST obtain a Return Merchandise Authorization (RMA) number from WGI Innovations, LTD. Please include name, UPS address (no P.O. Box), phone number, RMA number and a complete clarification of the problem on all enclosed correspondence. When possible, pack product carefully in original carton. Customers are responsible for any aircraft cost to WGI Innovations™. WGI Innovations™ will pay the shipping toll of replacement product to the customer, but is non responsible for impairment incurred in returning items for repair.

For product service send to:

WGI Innovations™
602 Fountain Parkway
Grand Prairie, TX 75050
(800) 847-8269

Customer SERVICE

WGI Innovations, LTD. stands behind every production we manufacture for a one-year product workmanship warranty and a strong commitment to customer service. If you are in need of customer service for missing parts or demand help with the functioning or assembly of your production, we encourage you to call one of our customer service representatives and let us assistance you lot.

DISCLAIMER

WGI Innovations, LTD reserves the right to make changes to product features, functionality and physical pattern at its sole discretion. As a result, such changes may not be reflected in this version of the manual.

FCC

FCC Statement

Product Name: Digital Game Scouting Camera
Merchandise Name: Wildgame Innovations

This device complies with Part 15 of the FCC Rules. Operation is subject to the post-obit ii criteria:

(1) This device may not cause harmful interference, and

(two) This device must have whatever interference received, including interference that may cause undesired performance.

Alert: Changes or modifications to this unit non expressly approved by the party responsible for compliance could void the user'south authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Course B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and tin can radiate radio frequency energy and, if non installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be adamant by turning the equipment off and on, the user is encouraged to attempt to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is continued.
Consult the dealer or an experienced radio/TV technician for assistance.

This device complies with Manufacture Canada licence-exempt RSS standard(s). Operation is subject area to the following two conditions:

(1) this device may non cause interference, and

(2) this device must accept any interference, including interference that may cause undesired functioning of the device.

Downloads

Wildgame Mirage User Manual – Download [optimized]
Wildgame Mirage User Manual – Download

Source: https://manuals.plus/wildgame-innovations/wildgame-mirage-manual

Posted by: mcdonaldyone1997.blogspot.com