How To Run Camera Wire Through Walls

Wires running forth the floor are cruddy and may pose a safety take a chance.

Need a new phone jack in your bedroom or installing speakers for your home theater organisation? While you could simply cord the wires along the floor, it'due south best to serpent the wires within walls or under floors.

Wiring new construction before the drywall goes in is a piece of cake compared to fishing them through existing walls and floors. But with careful planning, a few special tools, and the correct techniques, running wires in the wall of your abode may be easier than you might think.

If you're not up to the challenge, consider running the wires in special hollow moldings that have the place of standard crown molding or quarter round.

Tools

              Fish tape

Tools needed for running wires:

• Drill and bits
• Stud Finder
• Measuring Tape
• Flashlight
• Drywall keyhole Saw
• Fish Tape or Wire Coat Hanger
• Electrical Tape
• String and fishing weight

Earlier You First

• Check Building Codes: Most areas allow homeowners to install their own low-voltage wiring—such as phone lines, computer network cable, and speaker wire—simply check to be sure.



• Select Proper Wire or Cable: Make sure you use UL rated in-wall wiring that meets local edifice and fire codes—including CM, CMR, or CMP for estimator networking, and CL2 or CL3 for speakers.
• Turn off the Power: Always turn off the breakers in your electrical box before you lot begin to reduce the chance of an electrical shock should y'all accidently cut or drill into existing wiring.
• Avert Electrical Wires: Continue speaker, reckoner, and phone wires away from standard electrical wiring for safety reasons and to reduce interference.
• Choosing Walls: Whenever possible, run your wiring through interior walls, since exterior walls contain bracing and insulation.

Planning

Kickoff by taking some fourth dimension to consider the best location for the new wire. Eyeball existing electrical outlets, and make sure you're a safe distance abroad (the next stud over or more) to avoid interference or hitting existing wires.

Check the cranium for unseen problems like pipes and wires hidden in the wall.

Adjacent, examine the location from the attic, crawlspace, or basement to see if it's accessible and costless of hidden wiring or plumbing. It may also be a proficient idea to scan the wall using a metal detecting stud finder to locate obstacles like copper plumbing pipes and metal ductwork that may exist hidden in the wall.

Once your route has been mapped out, calculate the corporeality of wire or cable you'll need. Mensurate the distance from start to end, add together a few extra feet for connections, and an additional x% or so for unexpected problems or obstacles. The last matter y'all desire is to come upwards curt, so permit plenty extra and follow the old adage of "measure twice and cut once."

How to Fish Wires

1. When you're ready to begin, turn off the ability and use your stud finder to locate an open area in the wall between the studs.
2. Drill a pocket-size airplane pilot hole where the outlet volition be, and use a straightened metal coat hanger to experience inside the wall for any unforeseen obstructions. If you're looking for an alibi to larn the latest high-tech tool, a cable mounted inspection photographic camera, such as the Ridgid SeeSnake, makes a groovy way to meet within a wall.
3. If everything looks expert, overstate the hole for the wire or outlet box. Be sure to use an outlet boxes that'due south fabricated to attach to an existing wall, but don't install information technology until the wire has been run.


            Cutting hole in wall for outlet.                         Drill hole into wall plate.

4. Now, go up to your attic, or downwards to the basement or crawlspace, and drill a pigsty in the tiptop or bottom wall plate in the same wall cavity as the outlet.
5. Adhere the wire or cable to a fish tape or coat hanger using electrical tape, and feed it into the hole until it reaches the opening at the other end. If you're working from the cranium, you can drop a weighted string downwards wall cavity, and then attach the wire to the cord and pull it through.
6. Run the wire or cablevision to its destination. This may involve fishing it through some other wall cavity, or out a small hole drilled in the floor.


          Drill destination pigsty in floor.                       Run wire through hole.

7. Feed the wire through the back of the outlet box, insert the box in the wall, and mount it in place.
8. Strip the wires and adhere them to the wall jack or run them to the device.

Clean Upwards

If you lot drilled pilot holes that didn't piece of work out, patch them with a dab of spackling chemical compound. Sand the patch smooth when dry and touch on up with matching paint. Fill up whatsoever errant small holes in the floor with matching wood putty, and larger ones with a mixture of sanding dust and epoxy glue.

Source: https://todayshomeowner.com/how-to-run-wires-in-existing-walls-and-floors/

Posted by: mcdonaldyone1997.blogspot.com

Share this post